1. 'Datum' is the singular of 'data'.

2. Requests to make an objection shall specify the datum or data concerned

3. The sixth datum of each holding gives the number of indivisible 10-data groups.

4. How likely is this datum to be confused with other data if the representation is corrupted?

5. Note that criteria, data and dicta are plural words: the singulars are criterion, datum and dictum.

6. The data shall be communicated in computer readable form, as decimal degrees in the WGS-84 datum.

7. Length of the datum

8. Amaremus Datum registracije: 09.09.2010

9. Select planar surface or datum plane.

10. Definition of the datum points (see figure

11. And you'll build the firewalls to protect your datum?

12. An united space datum line has been given.

13. Potential is defined relative to an arbitrary datum.

14. Every theory, datum, or fact is generated by purpose.

15. Establishing datum plane is the base assessing surface parameter.

16. The tooling balls, datums , contour blocks, check pins etc, must be connected with the Car Coordinate System.

17. Go to datum point 69173 and tell Azrian you're there.

18. Then with A position datum and the surface processing.

19. THE ORIGINAL WORDING ABOUT THE CONCEPT OF SIZE DATUM.

20. By expressing the magnanimity datum with a small-scale network, clonal network structure was adopted in training the intrusion detection so as to get the compressed data.

21. horizontal datum point forward of V# and #° to the left (Pr

22. DataModel is the description of the selections and summary of datum.

23. Methods 36 clinical datum of immunity depression concurrence tuberculosis were analysised.

24. lower vertical datum point forward of V# and #° below the horizontal (Pr

25. The part of the world the piece of datum refers to.

26. Top illustration - Bottom surface is specified as Datum A and the surface at the 20 degrees basic (TED) angle has an Angularity tolerance of .13 relative to datum A.

27. Nunc tempus Acceptabile fulget datum divinitus, ut sanet orbem languidum medela parsimoniae

28. Geographic scope in which the local depth datum is practically used.

29. Determination of the datum points (example of a left-hand steering control vehicle

30. This paper dwells the concepts of retrogressive aggradation and the datum of erosion.

31. Water level determining the origin of depth measurements for the chart datum.

32. The arrangement has a datum and the aerofoil has a radial span.

33. Results Training samples were made up of 17 hospitals' index data in datum and corresponding comprehensive scores obtained by principal component method, the 18th hospital was used as testing sample.

34. Non quia quæro datum, sed requiro fructum Abundantem in ratione vestra

35. Concentricity: Concentricity is a median point centered to a datum axis control

36. We can solve these problems by using method of floating datum DMO superposition.

37. Google Earth uses Simple Cylindrical projection with a WGS84 datum for its imagery base.

38. A lower vertical datum point forward of V2 and 5° below the horizontal;

39. lower vertical datum point forward of V2 and 5° below the horizontal (Pr2);

40. The horizontal plane through the upper edge of the guiding device is the reference datum.

41. Concentricity does not control shape but Position of the shape to a fixed datum

42. Phl 4:17 - non quia quaero datum sed requiro fructum Abundantem in rationem vestram

43. Concentricity sets a limit on how non-symmetrical the shaft is relative to the datum axis

44. Concentricity is complex and rare as it controls opposed median points to a datum axis

45. (i) The positioning system and the SENC shall be based on the same geodetic datum.

46. An analog computer represents a datum as a voltage, distance, position, or other physical quantity.

47. The Concentricity control specifies that there is a 0.1 dia tolerance cylinder centered on datum [A]

48. Concentricity, sometimes called coaxially, is a tolerance that controls the central axis of the referenced feature, to a datum axis. The axes for the datum and referenced feature are derived from the median points of the part or feature.

49. 34) This clear datum of the tradition helps us to appreciate the inseparability of Christ and the Church.

50. What that means is that Circularity tolerance does not refer to or depends on any datum

51. Lowest astronomical tide (LAT) and Chart Datum (CD) – The lowest tide which can be predicted to occur.

52. The vertical datum is a surface to which elevations and/or depths (soundings and tide heights) are referred.

53. Height scanning interferometer for determining the absolute position and surface profile of an object with respect to a datum

54. The vertical datum line set up by this system can be used to monitor deformation of the various building.

55. A tidal surface datum approximating the level of the mean of the lower low water at spring tides.

56. The crucial datum is this: the rate of gypsy-moth spread is now much more rapid than before.

57. 1 A Hymn for Lent – Nunc tempus Acceptabile Nunc tempus Acceptabile Fulget datum divinitus, Ut sanet orbem languidum Medela parsimoniae

58. Philippians 4:17 non quia quaero datum sed requiro fructum Abundantem in rationem vestram Read verse in The Latin Vulgate w/ Apocrypha

59. The evaluate of noesis accruement exceeds the abilities of most scientists, and especially old scientists, to foreshorten by datum the direct literature.

60. Software for data searches, data aggregation, data analysis and data processing

61. Concentricity is the condition where the axis of all cross-sectional elements of a surface of revolution are common to the axis of a datum feature. A Concentricity tolerance specifies a cylindrical tolerance zone centered about the datum axis within which the axis of the controlled feature can be specified only on the RFS basic.

62. The data includes actual data and idle cell data.

63. Medical data management services, data aggregation services, data analysis services and data subscription services

64. Learrn how Microsoft Categorises data and view data categories, from customer data to administrator data

65. SAP BO Data Services (Bods) is an ETL tool used for data integration, data quality, data profiling and data processing

66. Related to Altitudinal: Altitudinal hemianopia, Altitudinal field defect altitude, vertical distance of an object above some datum plane, such as mean sea level sea level,

67. Anonymised data: data is unrecognisable, even to the data owner

68. Indicators of data accuracy: data accuracy measures or data accuracy ratings.

69. Data Sets control how uploaded data gets joined with existing data.

70. As of 2007, there was only one "very reliable"—still challenged—datum point identifying tropical tillites, which makes statements of equatorial ice cover somewhat presumptuous.

71. Caesarian Section Classification Dataset Data Set Download: Data Folder, Data Set Description

72. Data backup and data restoration services

73. Data transmission system and method for transmitting real time data and/or storage data in data communication networks

74. An interpolation data accumulation unit (112) accumulates received L-image data and R-image data as interpolation data.

75. ASME Y14.5 defines Concentricity as the requirement where the derived median points of all diametrically opposed elements must align with the axis of the datum feature

76. With these risk costs as a datum mark, we compare the general cost with the benefit of outsourcing, and then come into possession of boundary qualifica...

77. Atomising air connection General burner data Heavy fuel oil data General data Max

78. This process is called data accumulation or data enhancement in data mining lingo.

79. Claims data are the data collected during the servicing of claims under warranty and supplementary data are additional data such as production and marketing data.

80. On collecting datum of Bovine Epizootic Fever(BEF) from 1957 to 19 a long periods of gray model was established for forecasting BEF by using gray theories.